| Manufacturer Profile 01 | Western Europe | Hot-rolled U and Z sheet piles; interlocking sections; corner and junction piles | S235JR to EN 10025-2; sheet-pile delivery generally referenced to EN 10248-1 | Approx. 6–18 mm; standard mill lengths commonly 6–24 m, subject to transport limits | EN 10248-2 dimensional and shape tolerances; confirm width, height, thickness, straightness and interlock clearance | EN 10204 3.1
Heat number, chemical analysis, mechanical results and product identification required | Uncoated; shop-applied epoxy or polyurethane systems; zinc-rich primer where specified | Heat traceability from billet to finished pile; third-party inspection available by agreement | FCA, FOB, CFR or CIF under Incoterms® 2020; bundled and marked by heat or pack number | Request the approved section drawing and a signed tolerance schedule before production |
| Manufacturer Profile 02 | East Asia | Hot-rolled U-type sheet piles and fabricated accessories for temporary works | S235JR / S235J0 to EN 10025-2; equivalent grades require written approval | Approx. 7–20 mm; common commercial lengths 9–24 m, with cut-to-length service | Confirm EN 10248-2 compliance and interlock rotation, clutch width and pile camber limits | EN 10204 3.1
3.2 inspection can be arranged when required by contract | Mill finish; epoxy, coal-tar-free protective systems or temporary corrosion-prevention coating | Ultrasonic testing of specified welds or repaired areas; packing list linked to heat numbers | FOB or CFR for full cargoes; CIF or DAP may be quoted for smaller project lots | Confirm whether coating thickness is nominal dry-film thickness or total system thickness |
| Manufacturer Profile 03 | North America | Cold-formed and hot-rolled sheet piles; domestic and export project supply | S235-equivalent material must be expressly documented; EN 10025-2 compliance is preferable for S235 orders | Approx. 6–16 mm; typical lengths 6–18 m, subject to forming and handling capability | Use the applicable EN 10248-2 or ASTM project specification; do not assume equivalence without a comparison table | Verify format
Require EN 10204 3.1 or an agreed equivalent with heat-level results | Uncoated, galvanized or project-specified paint system; surface preparation grade must be stated | Dimensional report, chemical test and tensile test; independent inspector permitted | EXW, FCA, FOB, CFR or DAP depending on plant and destination | Check whether the quoted section is hot rolled or cold formed, because tolerances and interlock behavior differ |
| Manufacturer Profile 04 | Central Europe | High-volume Z-pile production; threaded bars, walers and corner solutions available | S235JR with minimum nominal yield strength of 235 MPa for relevant thickness range under EN 10025-2 | Approx. 8–25 mm; standard lengths generally 12–24 m, subject to rolling schedule | Measure section modulus, mass per metre, overall width, height and straightness against approved drawings | EN 10204 3.1
Certificate must identify grade, heat, product size and test direction where applicable | Uncoated; ISO 12944 paint systems; cathodic protection or corrosion allowance may be specified separately | Factory production control, calibrated gauges and photographic loading records available on request | FCA plant, CPT project port or DAP site; delivery split by installation sequence can be negotiated | Confirm effective width and theoretical mass, not only nominal pile width, for quantity calculations |
| Manufacturer Profile 05 | South Asia | U-pile and Z-pile sections; welded fabrication and project-specific cutting | S235JR / S235J0 to EN 10025-2; chemical composition limits must appear on the MTC | Approx. 6–22 mm; usual export lengths 6–21 m, with longer lengths subject to shipping approval | EN 10248-2 tolerance review plus inspection of pile end squareness and clutch condition | EN 10204 3.1
Include ladle analysis, tensile properties, impact results where specified and heat traceability | Shop primer, epoxy, polyurethane or duplex systems; coating repair procedure required for handling damage | Pre-shipment inspection, quantity check, marking verification and optional third-party laboratory testing | FOB, CFR or CIF; clarify whether port handling, fumigation and export documentation are included | Ask for a sample coating repair method and minimum acceptable repaired area before shipment |
| Manufacturer Profile 06 | Southeast Asia | Hot-rolled sheet piles for marine, foundation and temporary retaining applications | S235JR to EN 10025-2; alternatives such as ASTM grades should be separately approved | Approx. 7–19 mm; common supply lengths 9–24 m, depending on vessel and port restrictions | Confirm section geometry, straightness, end deformation and interlock tolerances after coating if coated | EN 10204 3.1
Digital PDF plus original or authenticated copy when required by contract | Mill finish; zinc-rich primer, epoxy or polyurethane; hot-dip galvanizing only when section size and standard permit | Marking at both ends or on each bundle; loading plan should identify bundle weight and heat range | CFR/CIF to main ports; DAP or DDP should be priced only after customs and inland transport review | Verify actual bundle weights against vessel limits and lifting equipment capacity |
| Manufacturer Profile 07 | Middle East | Project and stock-based sheet-pile supply; accessories and site delivery coordination | S235JR / S235J0 to EN 10025-2; grade designation must match the purchase order and drawings | Approx. 6–20 mm; stock lengths often 6–18 m, with mill production for longer sections | Require independent dimensional inspection because stock material may have been handled or previously stored | Confirm original MTC
Certificates must be linked to visible heat markings and bundle identification | Uncoated or field-applied protective coating; specify surface preparation, primer type and DFT | Visual inspection, dimensional survey and certificate review; NDT scope should be stated in the ITP | EXW, FCA, CPT or DAP; storage period and demurrage responsibility must be written into the offer | Check storage conditions, rust scale, clutch damage and remaining coating life for stock material |
| Manufacturer Profile 08 | Eastern Europe | Hot-rolled U and Z profiles; long-length production and rail or barge logistics | S235JR under EN 10025-2 with sheet-pile requirements under EN 10248-1 | Approx. 8–24 mm; lengths commonly 12–30 m when transport permits | Check EN 10248-2 limits plus straightness over full length and permissible end trimming tolerance | EN 10204 3.1
3.2 inspection may be included for infrastructure and marine projects | Uncoated or ISO 12944 C3–C5 coating system selected according to exposure category | ITP, calibration certificates, batch photographs and loading inspection available by contract | FCA, CPT, DAP or rail-delivered terms; define unloading point and crane responsibility | Review the proposed transport method for bending risk and confirm maximum bundle length |
| Manufacturer Profile 09 | Latin America | Regional and export supply of U-type piles; cutting, drilling and fabricated steel accessories | S235JR to EN 10025-2 or documented equivalent accepted by the engineer | Approx. 6–18 mm; standard lengths commonly 6–18 m, with project cutting available | Confirm mass tolerance, section width, profile height, clutch alignment and residual camber | EN 10204 3.1
Require bilingual certificate format if required for customs or project records | Mill finish; epoxy, polyurethane or zinc-rich systems; coating compatibility with welding must be documented | Batch identification, tensile testing and optional independent inspection before dispatch | FCA, FOB, CFR or CIF; include port storage, export packing and marine insurance responsibilities | Confirm whether cut lengths are supplied with factory-sealed ends and corrosion protection |
| Manufacturer Profile 10 | Oceania and export markets | Special-purpose sheet piles for marine works, temporary cofferdams and reusable systems | S235JR to EN 10025-2; durability design may require a corrosion allowance beyond the steel grade | Approx. 7–21 mm; typical lengths 9–24 m, subject to local lifting, road and port regulations | Require dimensional report at mill exit and confirmation that interlocks remain functional after transport | EN 10204 3.1
Certificate package should include MTCs, packing list, inspection release and nonconformance statement | Uncoated, marine epoxy, polyurethane or duplex coating; specify ISO 8501-1 preparation and DFT acceptance | Hold-point inspection, coating DFT readings and traceable nonconformance closeout | FOB, CFR, CIF, DAP or project-specific delivered-duty terms under Incoterms® 2020 | For marine exposure, verify coating specification, corrosion allowance, weld repair procedure and installation method |
.svg)
